TIPS ABOUT HOW TO Extend Smok Pen Recharge Time


TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is really a new pen that was developed by two guys in California. They wished to create a cool writing instrument that appeared as if a real pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.

smok pen

The Smok Pen has a built quality that’s just great. I found that even though it can be an electronic pen the build quality is just as good as any of the pens that I’ve reviewed. It is because of how they made the very best cap. You don’t need to be worried about the cap cracking or breaking on you Smok Valve Pen.

Both biggest differences that separate the Smok Valve from other pens may be the shape of the coils and just how that they are built. In general the coil on a Smok Pen is larger than on other pens. I think that they did this deliberately, to help make the pen feel more substantial.

If you take a look at a Smok Pen, you will observe that the body of the pen is round rather than smooth like other pens. On the back of the pen there exists a little tab that houses the coil. When you press on the tab you can easily turn the heating element on and off. I must say i liked this feature because it allows me to use the Smok Pen 22 whenever I feel like smoking.

To utilize the Smok Pen you have to keep the heat button pressed. After the button is pressed, the heating element will begin to warm up. Once it gets to the appropriate temperature you can turn off the heating element. Smok recommends using a 22mm tank. I prefer a larger tank, but that’s just me.

Once you put your Smok Pen in to the tank you will notice a indicator light seriously. The indicator light will remain green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. You should always put your pen into the charger before you apply the e-liquids to the coil heads. It is also important to do this before putting your e-liquids in to the coil heads.

Once you have completed this step, it is best to check to see for anyone who is at the proper temperature for the coils to fire. If not then you should turn the energy off and try again. Should you be still not satisfied with your Smok Pen i quickly suggest you take it in for some troubleshooting. This is exactly what I would call the “troubleshooting process” because sometimes things just usually do not work as they should. I would recommend that you perform the next two steps, then go ahead and check the Smok Pen to see if it still gets the electronic charging port.

Prior to going any further you should remove the battery from your own pen and unscrew the magnetic cap. You should then remove the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. Once you have loosened this wire you can then access the sub-ohm. You should then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch the coils.

After you have placed the sub-ohm tank into the pen you need to then place the rest of the components including the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the energy and follow the on screen instructions. You should place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it cool off. When you first put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting will not automatically get set you then should follow the on screen instructions.

Once the Smok Pen has reached the temperature that it Puff Bar Flavors requires to reach you need to then connect both wires to the negative and positive on the positive post on the Smok unit. You need to then connect the other end of the battery to the negative post on the negative side of the Smok unit. The ultimate step is to connect the positive cable to the bottom of the Smok’s power switch.

After all of the components have been placed into the pen, you should turn the energy on. After the first test run, you need to be able to see the battery life indicator light come on. If you do not see any sign of life from the Smok Pen, you need to remove the battery from the pen and then replace it with a brand new one. For your convenience gleam green light which might be pressed so as to confirm the battery charging status. If you have done these things and you do not start to see the green light indicating charging, you need to replace the battery.